System Requirements for running upload/download software:
- PC with a 80286DX processor; no higher than Pentium II.
- Processor speed 300 MHz maximum.
- MS-DOS 5.0 or above.
- Operating System not newer than Windows 98LE.
- DOS's SHARE or other compatible file sharing driver.
- 2 MB of extended memory (RAM).
- VGA, or Super VGA graphics adapter and monitor.
- For stand-alone PC operation, a hard disk with at least 5MB of free space.
- Optionally a mouse or equivalent pointing device compatible with the Microsoft© or Logitech© mouse drivers. A mouse is HIGHLY recommended
- For remote programming, a Hayes©-compatible modem. Older is better.
- Note: The actual amount of free hard disk space required is determined by the number of Panel Support Modules (PSMs) used and the number of customers you maintain.
CS-5000
Supports CS-5000 Central Station Receiver (discontinued). Click the link below to download CS-5000 v2.40.
Download ZIP File (875 KB)
*Unzip this compressed file and open the ReadMe file. This text file contains directions for installing the software update. After the Setup.exe program is completed, your CS-5000 software will be updated.
RPM/2 Pro Shell
Control Panels Supported:
- ZX400 (v1.0x - v2.1x)
- ZX300 (v1.0x)
- ZX200 (v1.0x)
- Discovery 5000 (v2.0x - v3.2x)
- Discovery 3000 (v2.1x - v3.1x)
- Z2000 (v2.0x - v3.2x)
- Z1250 (v3.0x - v3.2x)
RPM/2 Pro Shell software is contained in self-extracting executable files. Please review the system requirements at the bottom of this page. For security reasons these files are encrypted. You will need to obtain a password from technical support. After downloading, you must extract the file to a pre-formatted 3.5" HD floppy disk. When extracting the file you need to specify the destination drive. The following is an example.
c:\shell -password a:
After you have properly extracted the file you can run the install program from the floppy disk.
Download RPM/2 Pro Shell v2.00 for DOS (1108K), filename: shell.zip
Download RPM/2 Pro for DOS User's Guide, filename: rpmguide.pdf
RPM/2 Pro Panel Support ModulesPanel Support Modules (PSMs) are contained here in self-extracting executable files. After downloading the desired PSM you must extract the file to a pre-formatted 3.5" HD floppy disk. When extracting the file you need to specify the destination drive. The following is an example.
c:\pro200 -password a:
After you have properly extracted the file you can run the install program from the floppy disk.
Download PRO400 v2.05: ZX400 v2.1x & v1.0x (1034K), filename: pro400.zip
Download PRO300 v2.02: ZX300 v1.0x (529K), filename: pro300.zip
This PSM is compatible with ZX300 v1.0x control panels.
Download PRO200 v2.06: ZX200 v1.0x (529K), filename: pro200.zip
This update adds a feature to automatically process the re-configuration of Zone 8 on older versions of the ZX200.
Download PRO2500 v2.00: ESL2500 v1.2x (518K), filename: pro2500.zip
This PSM, which communicates with the ESL2500 via a DAC, can be used with version 1.2x control panel software.
Download PRO1250 v2.10: Z1250 v3.2x & v3.1x (1077K), filename: pro1250.zip
Download PRO2000 v2.10: Z2000 v3.2x & v3.1x (1080K), filename: pro2000.zip
Download PRO5000 v2.10: D5000 v3.2x & v2.1x (1087K), filename: pro5000.zip
Download UPG2000 v2.00: Z2000 v2.1x & v2.0x (1009K), filename: upg2000.zip
Download UPG5000 v2.00: D5000 v2.1x & v2.0x (1023K), filename: upg5000.zip
Obsolete RPM/2 Pro Panel Support Modules:
PRO3000 v2.00: D3000 v3.1x & v2.1x
PRO2000 v2.00: Z2000 v3.1x & v3.0x
PRO1250 v2.00: Z1250 v3.1x & v3.0x
The following PSMs are only supported by the original version of RPM2 (v1.41):
Z1200 v2.0x
Impact 300 v1.02-v1.04
Scanpro 4.0 Software InstallerControl Panels Supported: SP650, SP750, SP850, SC800/1600, AV9000.
The software is contained in a compressed archive using WinZip. After downloading the compressed file you must extract the files.
Download Scanpro 4.0 Software Installer (978K), filename: scanpro4.zip
Transport-PC rev 4.00This updated version of Transport-PC addresses year 2000 issues in the following Sentrol/Moose panels: Z700, Z900, Z880, Z950, Z1100E, D1000.
The software is contained in a self-extracting executable file. For security reasons this file is encrypted. You will need to obtain a password from technical support. After downloading the compressed file you must extract the files. The following is an example.
c:\Tpc4 -password a:
- D3000 v2.00
- D5000 v1.41
- Z1200 v2.00 - v3.00
- Z1250 v2.00
- Z2000 v2.00
- Impact300 v1.02 - v1.04
RPM/2 Shell software is contained in self-extracting executable files. For security reasons these files are encrypted. You will need to obtain a password from technical support. After downloading, you must extract the file to a pre-formatted 3.5" HD floppy disk. When extracting the file you need to specify the destination drive. The following is an example.
c:\shell -password a:
After you have properly extracted the file you can run the install program from the floppy disk.
RPM/2 Panel Support Modules
Panel Support Modules (PSMs) are contained here in self-extracting executable files. After downloading the desired PSM you must extract the file to a pre-formatted 3.5" HD floppy disk. When extracting the file you need to specify the destination drive. The following is an example.
c:\pro200 -password a: